Contents Disclaimers Important Notice FCC Compliance Support and Contact Information HANDLING AND SAFETY INSTRUCTIONS Safety Symbols Information IMPORTANT INVERTER SAFETY INSTRUCTIONS Chapter 1: Introducing the SolarEdge Power Harvesting System SolarEdge Power Optimizer Three Phase Inverter with synergy technology SolarEdge Monitoring Platform Supported AC Grids Installation Procedure Installation Equipment List Chapter 2: Installing the Power Optimizers Safety Package Contents Installation Guidelines Step
Maintenance Information Step 3: Verifying Proper Activation and Commissioning Reporting and Monitoring Installation Data The SolarEdge Monitoring System Providing Installation Information Site Mapper Application Creating a Site in the SolarEdge Monitoring Platform Paper Template Viewing System Status Main Inverter Status Multiple Inverters Status Communication Status Inverter Energy Status Meter Status Chapter 6: Setting Up Communication Communication Options Ethernet RS485 Wi-Fi GSM Communication Connector
Replacing the Primary Unit Replacing a Secondary Unit Replacing the Connection Unit Removing the Connection Unit Installing a New Connection Unit Connecting the Connection Unit to the Primary Unit Replacing Power Optimizers 79 80 81 81 81 82 82 Technical Specifications.............................................................................................................85 4 Three Phase Inverter with synergy technology Guide MAN-01-00401-1.
Version History l l Version 1.1 - Editorial updates (March 2018) Version 1 - (February 2018) 6 Three Phase Inverter with synergy technology Guide MAN-01-00401-1.
HANDLING AND SAFETY INSTRUCTIONS HANDLING AND SAFETY INSTRUCTIONS During installation, testing and inspection, adherence to all the handling and safety instructions is mandatory. Failure to do so may result in injury or loss of life and damage to the equipment. Safety Symbols Information The following safety symbols are used in this document. Familiarize yourself with the symbols and their meaning before installing or operating the system. WARNING! Denotes a hazard.
IMPORTANT INVERTER SAFETY INSTRUCTIONS WARNING Before operating the inverter, ensure that the inverter is grounded properly. Avant d''utiliser l''onduleur monophasé, est correctement mis à la terre. WARNING! Opening the inverter and repairing or testing under power must be performed only by qualified service personnel familiar with this inverter. L''unité ne doit être ouverte que par un technicien qualifié dans le cadre de l''installation et de la maintenance.
HANDLING AND SAFETY INSTRUCTIONS NOTE The symbol appears at grounding points on the SolarEdge equipment. This symbol is also used in this manual. NOTE A SolarEdge inverter may be installed in a site with a generator, however must not operate at the same time as the generator. Operating an inverter and a generator simultaneously will void the warranty. SolarEdge requires installing a physical or electronic interlock, which will prevent the generator and inverter from operating simultaneously.
Chapter 1: Introducing the SolarEdge Power Harvesting System Chapter 1: Introducing the SolarEdge Power Harvesting System The SolarEdge power harvesting solution is designed to maximize the power output from any type of solar Photovoltaic (PV) installation while reducing the average cost per watt. The following sections describe each of the system''s components.
Three Phase Inverter with synergy technology l l Module Add-on power optimizer – connected to one or more modules Smart modules - the power optimizer is embedded into a module Three Phase Inverter with synergy technology The Three Phase Inverter with synergy technology inverter (referred to as ''inverter'' in this manual ) efficiently converts DC power from the modules into AC power that can be fed into the main AC service of the site and from there to the grid.
Chapter 1: Introducing the SolarEdge Power Harvesting System SolarEdge Monitoring Platform The SolarEdge monitoring platform enables monitoring the technical and financial performance of one or more SolarEdge sites. It provides past and present information on the system performance both at the system and module levels. Supported AC Grids The following section shows the AC grids supported by the inverters (model dependent).
Installation Equipment List l l l l l l l l l l 17/32 HEX Allen screwdriver for AC stud connector SolarEdge supplied level Standard flat-head screwdrivers set Non-contact voltage detector Cordless drill or screwdriver and bits suitable for the surface on which the inverter will be installed and for opening the Connection Unit drill guides. Use of an impact driver is not recommended.
Chapter 2: Installing the Power Optimizers Chapter 2: Installing the Power Optimizers Safety The following notes and warnings apply when installing the SolarEdge power optimizers. Some of the following may not be applicable to smart modules: WARNING! The metallic enclosure of the power optimizer must be grounded in accordance with the product''s listing and local and national codes.
Package Contents CAUTION! Installing a SolarEdge system without ensuring compatibility of the module connectors with the optimizer connectors may be unsafe and could cause functionality problems such as ground faults, resulting in inverter shut down. To ensure mechanical compatibility of the SolarEdge optimizers'' connectors with the PV modules'' connectors to which they are connected, use identical connectors from the same manufacturer and of the same type on both the power optimizers and on the PV modules.
Chapter 2: Installing the Power Optimizers and other surfaces, on all sides except the mounting bracket side. Figure 4: Power optimizer clearance NOTE The images contained herein are for illustrative purposes only and may vary depending on product models. Step 1: Mounting and Grounding the Power Optimizers For each of the power optimizers1: 1.
Step 1: Mounting and Grounding the Power Optimizers WARNING! The metallic enclosure of the power optimizer must be grounded in accordance with the requirements of the local and national codes. L''enceinte métallique de l''optimiseur de puissance doit être mise à la terre en accord avec les régulations locales et nationales. l For mounting on a grounded metal rail: Use the provided 5/16'''' stainless steel grounding star washer between the railing and the flat side of the mounting bracket.
Chapter 2: Installing the Power Optimizers Figure 7: Power optimizer grounding terminal 5. Verify that each power optimizer is securely attached to the module support structure. 6. Record power optimizer serial numbers and locations, as described in Reporting and Monitoring Installation Data on page 48 Step 2: Connecting a PV Module to a Power Optimizer NOTE Images are for illustration purposes only. Refer to the label on the product to identify the plus and minus input and output connectors.
Step 3: Connecting Power Optimizers in Strings NOTE l l Use at least 11 AWG/ 4 mm² DC cables. The total conductor length of the string (excluding power optimizers'' conductors; including home runs and necessary extensions between optimizers) should not exceed: o For inverter models SE14.4K and SE33.3K - 2300 ft./ 700 m from DC+ to DC- of the inverter IMPORTANT SAFETY FEATURE l l For a compliant PV Rapid Shutdown (PVRSS) installation, use no more than 30 optimizers per string.
Chapter 2: Installing the Power Optimizers Step 4: Verifying Proper Power Optimizer Connection When a module is connected to a power optimizer, the power optimizer outputs a safe voltage of 1V. Therefore, the total string voltage should equal 1V times the number of power optimizers connected in series in the string. For example, if 10 power optimizers are connected in a string, then 10V should be produced. Make sure the PV modules are exposed to sunlight during this process.
Chapter 3: Installing the Primary and Secondary Unit(s) Chapter 3: Installing the Primary and Secondary Unit(s) Install the units either before or after the modules and power optimizers have been installed. First install the Primary Unit, then the Secondary Unit(s) (in any order).
Chapter 3: Installing the Primary and Secondary Unit(s) l ON/OFF/P Switch: Figure 11: ON/OFF/P switch o o o ON (1) - Turning this switch ON (after optimizer pairing) starts the operation of the power optimizers, enables power production and allows the inverter to begin exporting power to the utility grid OFF (0) - Turning this switch OFF reduces the power optimizer voltage to a low safety voltage and inhibits exportation of power.
Primary Unit Interface Figure 12: LEDs The following table describes system performance information by LED color and ON/OFF/P switch position.
Chapter 3: Installing the Primary and Secondary Unit(s) The following table describes production percentage of AC information by LED color and ON/OFF/P switch position.
Secondary Unit Interface Communiation Cable DC Cable o AC Cable DC conduit entry: DC conduit for connecting the PV DC drill guide :DC drill guide for connecting the PV AC drill guide entry : AC drill guide for grid connection Communication gland: for connection of communication options. Refer to Setting Up Communication on page 56.
Chapter 3: Installing the Primary and Secondary Unit(s) 2. Loosen the screws on the front cover of the Connection Unit. Figure 15: Opening the Connection Unit cover 3. Remove the Connection Unit cover. 4. Open the required AC and DC conduit drill guides according to the conduits used in the installation. The drill guides are located at the bottom of the enclosure. l Knockout the DC drill guide (conduit entry) 1.25".
Mounting and Connecting the Primary and Secondary Unit(s) Mounting and Connecting the Primary and Secondary Unit(s) The inverter is typically mounted vertically, and the instructions in this section are applicable for vertical installation. Some SolarEdge inverters model can be installed horizontally (above 10° tilt) as well as vertically. For information and instructions for horizontal mounting refer to
Chapter 3: Installing the Primary and Secondary Unit(s) 2. To allow proper heat dissipation, maintain the following minimum clearance areas between the inverter and other objects: NOTE The Primary unit is longer than the Secondary Unit, therefore make sure the mounting location is high enough to fit the Primary Unit and leaves sufficient space for cable entry. l l If installing a single inverter: o 8" (20 cm) from the top of the unit.
Mounting and Connecting the Primary and Secondary Unit(s) l l l Lift the Primary Unit from its sides. Align the two indentations in the enclosure with the two triangular mounting tabs of the bracket, and lower the unit until it rests on the bracket evenly (see Figure 18). Insert the supplied screw through the right side of the heat sink and into the bracket Figure 18: Hanging units 8. Mount the Secondary Unit(s): l l l l There is no specific order for hanging the Secondary Units.
Chapter 3: Installing the Primary and Secondary Unit(s) l Communication cable to communication connector l DC cables to DC+ and DC- connectors l AC cable to AC connector o Ensure the white mark on the AC connector, is lined between the arrows on the AC cable. o Plug the AC cable into the Secondary Unit. o Rotate the cable connector clockwise to fasten it.
Mounting and Connecting the Primary and Secondary Unit(s) 11. Assemble the two parts of the cable lock (supplied with the inverter) around the cable connector, making sure that the orientation of the printed text on the lock is correct. Push the parts together until they click to lock. To open the lock use a flat-bladed screwdriver. Figure 22: Cable lock 31 Three Phase Inverter with synergy technology Guide MAN-01-00401-1.
Chapter 4: Connecting the AC and Strings to the Connection Unit Chapter 4: Connecting the AC and Strings to the Connection Unit The Safety Switch in the Connection Unit disconnects all ungrounded DC conductors in compliance with the National Electric Code (NEC; Specifically NEC690.35, which addresses ungrounded PV arrays). The Connection Unit is rated to the maximum operating conditions of the inverter. Inverters of different models might be equipped with different sizes/ types of terminal blocks.
Connecting the AC Grid and Grounding to the Connection Unit To connect AC and ground: 1. Turn OFF the AC circuit breaker. 2. Open the Connection Unit cover: Release the six Allen screws and carefully move the cover horizontally before lowering it. CAUTION! When removing the cover, make sure not to damage internal components. SolarEdge will not be held responsible for any components damaged as a result of incautious cover removal. 3. Remove the terminal block cover. 4.
Chapter 4: Connecting the AC and Strings to the Connection Unit 9. Apply heat shrink insulation to the lugs barrels. 10. Connect the wires to the terminal blocks with a proper tool according to the labels on the terminals. 11. Tighten the screws of each terminal with a torque of 15N*m / 12 lb*ft. Wire type Connect to terminal Line 1 L1 Line 2 L2 Line 3 L3 Neutral N Figure 25: Wire connections to terminal block 12. Place the cover on the terminal block and push until lyou hear a click.
About Solaredge 100kw inverter manual
As the photovoltaic (PV) industry continues to evolve, advancements in Solaredge 100kw inverter manual have become critical to optimizing the utilization of renewable energy sources. From innovative battery technologies to intelligent energy management systems, these solutions are transforming the way we store and distribute solar-generated electricity.
When you're looking for the latest and most efficient Solaredge 100kw inverter manual for your PV project, our website offers a comprehensive selection of cutting-edge products designed to meet your specific requirements. Whether you're a renewable energy developer, utility company, or commercial enterprise looking to reduce your carbon footprint, we have the solutions to help you harness the full potential of solar energy.
By interacting with our online customer service, you'll gain a deep understanding of the various Solaredge 100kw inverter manual featured in our extensive catalog, such as high-efficiency storage batteries and intelligent energy management systems, and how they work together to provide a stable and reliable power supply for your PV projects.
